Для заявок - dmc@itmash.ru Miniature Adjustable Crimp Tools LOWER RANGE CRIMP MILITARY P/N DMC P/N DESCRIPTION NSN TOOL AFM8 M22520/2-01 M22520/2-01 AFM8 TOOL FRAME 5120-01-335-8572 Qualified to MIL-DTL-22520/2*, M22520/2-02 K1S POSITIONER 5120-01-335-8592 the DMC AFM8 is designed for most M22520/2-03 K60S POSITIONER 5120-01-335-8593 of the miniature and sub-miniature M22520/2-04 K151 POSITIONER 5120-01-335-8594 connector types that are so widely M22520/2-05 K3 POSITIONER 5120-01-335-8595 used in electronic systems. The AFM8 M22520/2-06 K41 POSITIONER 5120-01-335-8624 meets the need for a miniature tool M22520/2-07 K40 POSITIONER 5120-01-335-8625 accommodating wire sizes 20 through M22520/2-08 K13-1 POSITIONER 5120-01-335-8626 32 AWG. M22520/2-09 K42 POSITIONER 5120-01-335-8627 M22520/2-10 K43 POSITIONER 5120-01-335-8628 The AFM8 gives a Mil-Standard M22520/2-11 K287 POSITIONER 5120-01-335-8629 8 impression crimp, which assures M22520/2-12 K286 POSITIONER 5120-01-335-8630 maximum tensile strength. The cycle M22520/2-13 K338 POSITIONER 5120-01-335-8631 controlled precision ratchet assures M22520/2-14 K340 POSITIONER 5120-01-335-8632 consistently accurate crimps every time. M22520/2-15 K341 POSITIONER 5120-01-335-8633 The tool frame has a built-in 8 step M22520/2-16 K339 POSITIONER 5120-01-335-8634 selector knob for ease in dialing the M22520/2-17 K342 POSITIONER 5120-01-335-8635 correct crimp depth setting for the wire M22520/2-18 K343 POSITIONER 5120-01-335-8636 being used. M22520/2-19 K330-2 POSITIONER 5120-01-335-8637 M22520/2-20 K331-2 POSITIONER 5120-01-335-8638 Positioners adapt the tool frame to M22520/2-21 K332-2 POSITIONER 5120-01-335-8609 a particular application. The data plate M22520/2-22 K212 POSITIONER 5120-01-335-8610 on each positioner designates which M22520/2-23 K267-1 POSITIONER 5120-01-335-8611 contacts the positioner accommodates M22520/2-24 K75S-1 POSITIONER 5120-01-335-8612 for its wire size and indicates selector M22520/2-25 K261-1 POSITIONER 5120-01-335-8613 position. The positioner is easily removed M22520/2-26 K262-1 POSITIONER 5120-01-335-8614 and changed. M22520/2-27 K269-1 POSITIONER 5120-01-335-8615 M22520/2-28 K373-1 POSITIONER 5120-01-335-8616 Periodic gaging is recommended to M22520/2-29 K372-1 POSITIONER 5120-01-335-8617 insure accurate calibration. This is easily M22520/2-30 K404 POSITIONER 5120-01-335-8618 accomplished with the M22520/3-1 M22520/2-31 K406 POSITIONER 5120-01-335-8619 “GO/NO-GO” gage (DMC part no. G125) M22520/2-32 K496 POSITIONER 5120-01-335-8620 on SEL setting #8. The AFM8 is 6 3/4" in M22520/2-33 K74S POSITIONER 5120-01-335-8621 length and weighs approximately 10 oz. M22520/2-34 K323 POSITIONER 5120-01-335-8622 M22520/2-35 K532-1 POSITIONER 5120-01-335-8623 Other than keeping the tool clean M22520/2-36 K473 POSITIONER 5120-01-335-8596 and properly stored when not in use, M22520/2-37 K709 POSITIONER 5120-01-361-9666 no operator maintenance is required. M22520/3-1 G125 5220-01-016-6002 Pneumatic versions of this tool are found GAGE on page 12. SK2/2 ADJUSTABLE 5120-01-171-1569 POSITIONER The DMC274 tool kit contains the DMC274 M22520/2 TOOL KIT 5180-01-259-0512 AFM8 tool frame, tool gage, and all mil-spec positioners. Also included in www.itmash.ru the DMC274 are tool instruction sheets dmc@itmash.ru and a tool selection chart. +7 (495) 668-13-58 * Change to SAE AS22520 in process consult DMC for status. PAGE 8